• Flat rate shipping costs
  • Fast DHL shipping
  • Location Germany
  • Satisfied customers in 43 countries
  • Service: +49 (0) 8074 91 72 42 1
  • Flat rate shipping costs
  • Fast DHL shipping
  • Location Germany
  • Satisfied customers in 43 countries
  • Service: +49 (0) 8074 91 72 42 1

CYANOLIT 202 | 2g TT & 20g | superglue with delayed hardening

from 2.85 €

Delivery time: ca. 3-10 day(s)

Description

CYANOLIT 202 glue in 2g TT and 20g is a superglue with delayed hardening, higly transparent for more time while glueing.

CYANOLIT 202, low viscosity with delayed hardening

 

Cyanolit®202 is a low-viscosity cyanoacrylate adhesive with good wetting properties. The delayed hardening enables a subsequent positioning of the joined parts and a low-tension gluing.

With the Cyanolit® instant adhesive series, Panacol-Elosol offers an optimal product range in the area of ​​cyanoacrylates (ethyl-2-cyanoacrylate). Cyanolit® seconds adhesives are solvent-free reactive adhesives in the field of cyanoacrylates, which are formulated on the basis of esters of cyanoacrylic acid. They show very good adhesion to many materials and especially plastics.

  • Viscosity (mPas) 70 - 100  (Brookfield LVT, 25°C, Sp 2/60rpm)
  • Density (g/cm3) 1,1  (PE-Norm 004)
  • Flash point (°C) >83  (PE-Norm 050)
  • Refractive index (nD20) 1,5  (PE-Norm 018)
  • Heat emission constant (10kHz) 126
  • Volume resistance (Ohm*cm) 8,4E+12  (PE-Norm 040)
  • Temperature resistance (°C) -80 - 80
  • Storage (°C) at room temperature max 25°C
  • Shelf life in the unopened original container at delivery min. 4.5 months max. 9 months

Curing

Curing takes place without the addition of heat, expensive pressure or additional activators. The classic one-component cyanoacrylates react with air moisture, which is absorbed as a moisture film on the material surfaces, in a few seconds.

The curing speed depends on the gap width and the level of air humidity. A small gap width and high air humidity accelerate the setting process.

Cyanolit®202 reaches high strengths after a short time. The material continues to harden 24 hours after bonding. The optimum media resistance is only achieved after this time. The table below describes the setting times on various substrates.

Material Setting time (sec.) Bond strength (MPa)
PVC hard 13 5,1*
ABS 25 5,4*
PA 6.6 40 4,7*
PVC/Steel 30 7,0*
AI/ABS 60 5,0*
Neopren/Steel 60 0,5*
NBR 50 0,5*

*Substrate breakage

Processing instructions

Surface preparation

The surfaces to be glued should be free of dust, oil, grease or other soiling in order to obtain an optimal and reproducible glue.

We recommend Panacol's IP® cleaner for cleaning. Substrates with low surface energy (e.g. polyethylene, polypropylene) must be pretreated in order to achieve sufficient adhesion.

Adhesive application

Our products are delivered ready to use. Depending on the packaging, they can be dosed by hand directly from the container or semi-automatically or fully automatically. In specific cases, please contact our application technology.

Cyanoacrylate adhesives react very quickly with air humidity (20% - 80%) or the moisture film on the materials. It is therefore advisable to wear gloves and safety glasses when handling large quantities. Cyanolite is applied in spots - one or more drops, depending on the size of the surface - to one of the parts to be joined. The second joint is fixed with light pressure, which spreads the adhesive into a thin film. Acidic surfaces prevent or delay the setting, while basic surfaces (pH> 7) accelerate the setting.

The application can be done directly from the tip of the dosing bottle, but also with dosing devices. Since the achievable strength depends on the application quantity, care must be taken to ensure even dosing.

Glue and parts to be joined must not be cold, they must be warmed to room temperature before processing.

For safety information, please refer to the safety data sheet / product data sheet

Hints

The product is free of heavy metals, PFOS and phthalates and is compliant with the EU Directive 2017/2102 / EU "RoHS III".

Our data sheets have been compiled based on current knowledge. The data given therein are for the information of the user only and do not describe any legally binding properties. We recommend checking our products to determine whether they meet the user's intended purpose.

App